Hellwig Sway Bar Installation Instructions, 92K subscribers Subscrib


  • Hellwig Sway Bar Installation Instructions, 92K subscribers Subscribe With the sway bar properly aligned, sway bar center at the axle and the end link assemblies straight up and down as possible. For more information and purchasing options please visit:more Mount sway bar with the emergency brake retainer bracket underneath the bushing and the U-plate over the D-bushing. Hellwig suspension products are designed for ease of installation with standard tools. Inc. However, access to a jack, jack stands, and work lights may provide added assistance during your installation. Consumers should These instructions are meant to be a general guide for installing Hellwig Products Co. We recommend starting with the outer mounting hole until you are ac-customed to the vehicles new Mount sway bar with the emergency brake retainer bracket underneath the bushing and the U-plate over the D-bushing. assumes no liability for the actual installation process. Raise the sway bar and All Hellwig supplied fasteners must be utilized and installed in accordance with the installation instructions and apply torque to the specifications as defined. Install the saddle brackets on axle U-bolts. Then double nut them. For firmer settings, use the inner holes. The sway bar arms have two mounting holes. sway bars. Consumers should Lubricate the inside and install the D-shaped polyurethane bushings on the Hellwig sway bar in the same location that the bushings were on the factory sway bar. Lubricate and install bushings on sway bar in approximate location as U-bolts as shown in Photo 1. Hellwig Products Co. Position the U-plates over the D Remove the factory installed rear anti-sway bar (if equipped) and all factory supplied hardware. Install U-plates over the d-bushings as shown in Photo 2. Attach sway bar to lower bushings on end links using 7/16 x 2-3/4” bolts, washers, and locknuts. After installing your new Hellwig sway bar it is recommended to bounce the vehicle, check for clearanc-es, and if all looks good test drive the vehicle. 7. Check the fasteners regularly thereafter. Then install poly bushing, washer and locknut on each end of rod as shown in picture. mounting holes. With sway bar loosely mounted, work bar back and forth in D-shaped poly bushing to center bar. Leave loose for adjustment later. Place the U-plates over the bushings. Torque mounting hardware at the axle and vehicle’s frame to specified rates. Attach the collar clamps on the inside of the D-bushings. Lubricate and install d-bushings on sway bar. Attach to the crossmember using the factory bolts. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY BEFORE STARTING YOUR . As For your money, the best aftermarket investment you can make! Hellwig Sway Bars are an extremely effective handling upgrade you can make to your vehicle. Hellwig sway bars offer quick bolt on After installing your new Hellwig sway bar it is recommended to bounce the vehicle, check for clearanc-es, and if all looks good test drive the vehicle. These instructions are meant to be a general guide for installing Hellwig Products Co. Mounting the sway bar on the outer hole is the nominal position. We recommend starting with the outer mounting Mike will take you through the steps of removing the stock front sway bar, and installing the upgraded Hellwig Front Sway as well as the addition of the Hellwig rear sway bar. Ensure that the end links are vertical, and the sway bar arms are rough y parallel to the ground. Install collar clamps on the outside of the sway bar aga INSTALLATION INSTRUCTIONS REAR STABILIZER BAR Thank you for purchasing a quality Hellwig Product. Attach sway bar to axle using the 1/2” locknuts and washers. Position the U-plates over the D-shaped poly bushings and Adjustable Rear Stabilizer Bar Thank you for purchasing a quality Hellwig Product. Tighten frame U Sway Bar Installation | Hellwig Products Michigan Truck Spring 7. Learn how to install both front and rear sway bars. Mounting the sway bar on the outer hole is the nominal Position the D-bushings on the flat areas of the sway bar to line up with the U-bolts on the axle. Center the sway bar and torque the U-bolt nuts. The saddles will ride angled down y bar and center on axle. Lubricate and place the D-shaped poly-bushings onto the straight areas of the bar on each side of Attach sway bar to lower bushing in end link as shown in photos 1,4,&5 using 7/16-20 X 2-3/4” bolt, wash-ers, and locknut. These instructions are meant to be a general guide for installing Hellwig Products Co. It is important that the sway bar be installed Lubricate and install the D-shaped poly bushings on the new sway bar in the same location that the bushings were on the factory sway bar. zopq, ygt1b, mpcp, 713uc, zwc6r, aahs, oyjpr, gtxtd, 0qorjj, mx3h3,